Skip to content Skip to navigation Skip to footer
POLARIS OFF-ROAD VEHICLES
HELP CENTER
11/03/2026

2027 RZR Pro R Boost Spark Plug Service

Required Tools and Supplies

  • T40 TORX® Socket

  • 8mm Socket

  • 10mm Socket

  • Spark Plug Wrench (Provided in Tool Kit)

  • Ratchet

  • Torque Wrench

  • Dielectric Grease or Petroleum Jelly

  • Air Chuck

  • Pliers

  • Flashlight

  • Eye Protection

  • Nitrile Gloves

  • Shop Rags


To inspect and replace the spark plugs on your RZR Pro R Boost, follow these steps:

Always allow the engine to cool completely before performing this procedure. 

1. Park the vehicle on a flat, level surface in a well-ventilated area, and ensure the transmission is in PARK. Note: RZR Pro R Boost Ultimate model shown.

2. Remove the six cargo box fasteners using a T40 TORX® socket.
 
3. Remove the hose retention clips from the chassis member.

4. Lift the cargo box up and out to remove it from the vehicle.

5. Remove the four push-darts from the rear access panel using a push pin remover. Remove and set the push-darts aside.

6. Remove the four fasteners and four electric harness connections with an 8mm socket and a 10mm socket. Clean out the plug wells with compressed air from the air chuck to remove any loose dirt or debris.

7. Once complete, remove the ignition coils.

8. Carefully remove the spark plugs and remove from the vehicle using the provided spark plug wrench or a 5/8-in. spark plug socket with extension. Tip: If reusing, take note of the cylinders they were installed in for reinstallation.

9. Inspect the electrodes for wear and carbon buildup. The spark plug should have a sharp outer edge with no rounding or erosion of the electrodes.

10. Inspect the spark plugs for the correct color.

  • The normal insulator tip is gray, tan or light brown with few combustion deposits with unburnt and uneroded electrodes. This indicates the proper type and heat range for the engine and the service.

  • The tip should not be white. A white insulator tip indicates overheating caused by an improper spark plug or incorrect throttle body adjustments.

  • A wet fouled insulator tip is black. If it is black, this usually means excessive oil consumption, use of non-recommended oil, or poor fuel quality. 

11. Measure the spark plug gap with a wire gauge. Adjust the gap, if necessary, by carefully bending the side electrode. The gap should measure 0.7 – 0.8 mm.

12. If necessary, replace with the recommended spark plug (part number 3023173). Important: Severe engine damage may occur if the incorrect spark plug is used.

13. Install the spark plugs into the engine and torque to 12 Nm (no anti-seize), 10 Nm (with anti-seize).

14. Before continuing, apply a light coat of dielectric grease to the bottom of the ignition coils.

15. Reinstall the ignition coils and ensure they are pushed all the way down, so they engage on the spark plugs. Torque fasteners to 7 ft-lbs (10 Nm).

16. Reconnect the ignition coil harness connectors and verify that the connections are properly secured.

17. Once complete, reinstall the engine access panel and cargo box. Torque to 31 in-lbs (3.5 Nm).

18. Reinstall the hose retention clips to the chassis member.

19. Start the engine to ensure proper operation.

For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
More maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC
TORX® is a registered trademark of Acument Intellectual Properties, LLC 
NGK® is a registered trademark of NGK Spark Plug Co., Ltd.
 

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2026 Polaris Industries Inc.

Keyword(s) spark , plug , service , diy , DIY , maintenance , procedure ,