Skip to content Skip to navigation Skip to footer
POLARIS OFF-ROAD VEHICLES
HELP CENTER
10/29/2026

2027 RZR Pro R Boost Drive Belt Inspection and Replacement

Required Tools and Supplies

  • T25 TORX® Socket

  • T40 TORX® Socket

  • 8mm Socket

  • 10mm Socket

  • Extensions

  • Ratchet

  • Flathead Screwdriver

  • Clutch Spreader Tool

  • Drive Belt

  • Torque Wrench

  • Eye Protection

  • Nitrile Gloves

  • Shop Rags


To inspect and replace the drive belt on your RZR Pro R Boost, follow these steps:

1. Park the vehicle on a flat, level surface, ensure it is in PARK and remove the key. Note: RZR Pro R Boost Ultimate model shown.

2. Begin by disconnecting the heated and ventilated seat connectors.

3. Remove both seats by pulling up on the seat latch lever located under the front edge of the seat. Tilt the seat forward and lift it upward to remove.

4. Remove the upper close-off panel by turning the four quarter-turn latches. Lift the panel up and pivot it out around the seat harnesses to remove.

5. Turn the two quarter-turn latches from the panel and two from inside the center console.

6. Remove the four fasteners below the center storage box with a T40 TORX® socket.

7. Remove the center console and remove the lower close off panel.

8. Thoroughly clean all debris from the engine compartment.

9. Once complete, loosen the clamps retaining the PVT inlet duct to the outer clutch cover using a flathead screwdriver.

10. Continue by carefully maneuvering the duct out of the vehicle and set aside.

11. Remove the worm clamp from the lower clutch duct using a flathead screwdriver.

12. Remove the debris shield using an 8mm socket and a T25 TORX® socket.

13. Remove the seven (7) clutch cover bolts securing the clutch cover using a 10mm socket.

14. Continue by maneuvering the outer clutch cover outward and upward to access the drive belt.

15. Make sure to take note of the drive belt direction of rotation so that it can be installed in the same direction.

16. Remove the clutch spreader tool from the top of the clutch housing and thread the tool into the driven clutch turning it clockwise to open the sheaves of the driven clutch.

17. Carefully walk the belt off the driven and drive clutch and remove.

18. Remove ALL debris wrapped in and around the PVT system and from the entire clutch air duct passage. Continue by checking for signs of damage to the seals on the transmission and engine. If any seals appear to be damaged, your vehicle requires prompt service. Your Polaris dealer can assist.

19. Inspect the belt for any fraying, hour-glassing, loose cords, missing cogs, abrasions, burns or damage, and replace if needed. A new drive belt is part number 3212366.

20. Ensure the belt is installed the same direction it was removed.

21. Loop the belt over the drive clutch and begin to walk it over the driven clutch sheave.

22. Remove the clutch spreader tool and return it to the clutch housing cover.

23. Rotate the driven clutch clockwise five to seven times to help seat the belt on the sheaves.

24. Reinstall the seven (7) clutch cover bolts securing the clutch cover and torque to 53 in-lbs (6 Nm).

25. Reinstall the debris shield. Torque to 54 in-lbs (6.1 Nm).

26. Reinstall the lower ducting to the clutch cover and torque to 27 in-lbs (3 Nm).

27. Once complete, reinstall the PVT inlet duct to the outer clutch cover and fasten with the clamp. Torque to 12 in-lbs (1.4 Nm).

28. Reinstall the lower close-off panel.

29. Reinstall four fasteners to the center console.

30. Secure the two quarter-turn latches inside the center console.

31. Secure the two quarter-turn latches on the lower close-off panel.

32. Continue by reinstalling the upper close-off panel and secure the four quarter-turn latches.

33. Slide the seat tabs at the front edge onto the seat retainer tubes. Then press down firmly at the rear of the seat to engage the rear latches. Ensure the seats are latched securely.

34. Reconnect the heated and ventilated seat connectors. Note: If the belt was replaced, follow the Owner’s Manual guidelines for belt break-in.
 

For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
More maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC
TORX® is a registered trademark of Acument Intellectual Properties, LLC 
 

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2026 Polaris Industries Inc.

Keyword(s) drive , belt , inspect , inspection , replacement , diy , DIY , maintenance ,