Required Tools and Supplies
- 6mm Allen Socket
- T40 TORX® Socket
- Ratchet
- Torque Wrench
- Oil Filter Wrench
- Oil Pan
- Funnel
- PS-4 Engine Oil
- Oil Filter
- Eye Protection
- Nitrile Gloves
- Shop Rags
For information on tools, read the Tools and Fasteners Guide.
Always wear safety glasses and nitrile gloves when servicing your Polaris RZR. For optimal performance, always use Polaris-recommended fluids as described in your Owner’s Manual. The oil change kit is part number 2881696.
To change the engine oil and filter on your RZR Pro S or Pro XP, follow these steps:
1. Park the vehicle on a flat, level surface in a well-ventilated area, ensure it is in PARK and remove the key.
2. Allow the engine to cool down before draining the oil.
3. Place a drain pan under the engine crankcase. Tip: Placing a rag at the bottom of the pan will help prevent the splashing of oil.
4. Clean the area around the drain plug.
5. Remove the drain plug with a 6mm Allen socket.
6. Remove the access panel behind the seats to access the oil filter. Note: The engine should be off for at least 2 minutes prior to removing the oil filter.
7. On 2-passenger models, remove both seats by pulling up on the seat latch lever located under the front edge of the seat and tilting the seat forward and upward to remove. On 4-passenger models, press on the upper seat latch and lift up to remove the seat backs.
8. Remove the upper access panel by turning the four (4) quarter turn latches and set aside.
9. Remove the lower access panel.
10. On 2-passenger models, turn the two quarter-turn latches from the panel and two from inside the center console. On 4-passenger models, remove the lower close-off panel by turning the two quarter-turn latches.
11. Use an oil filter wrench to turn the filter counterclockwise to remove. Tip the top end of the oil filter up to minimize oil spill. Tip: Place a shop rag under the oil filter to catch any spills.
12. Clean the filter sealing surface on the engine crankcase with a clean rag and ensure the original oil filter O-ring is not stuck to the crankcase.
13. Lubricate the O-ring on the new oil filter with a film of clean engine oil. Check to make sure the O-ring is in good condition. A new filter is part number 2521728.
14. Install the filter by hand until the filter O-ring contacts the sealing surface, then turn an additional 3/4 turn.
15. Inspect the sealing washer on the drain plug for burrs or nicks and replace the washer if it is damaged.
16. Reinstall the drain plug and torque to 12 ft-lbs (16 Nm).
17. Remove the cargo box by removing the four rear-most fasteners with a T40 TORX® socket.
18. Clean the area around the oil fill cap and add the recommended oil through the oil fill cap located on top of the engine valve cover. Do not overfill. One quart of PS-4 5W-50 oil is part number 2876244. One gallon of PS-4 5W-50 oil is part number 2876245. The oil capacity is 2.75 qts (2.6 L).
19. Start the engine and allow it to idle for 30 seconds.
20. Stop the engine and inspect for leaks. Wait at least 15 seconds before removing the dipstick.
21. Unlock the dipstick lever and remove the dipstick. Wipe it dry with a clean shop rag.
22. Reinstall the dipstick fully and remove again to inspect the oil level. Note: Make certain the dipstick is inserted all the way down to ensure an accurate reading.
23. Add the recommended oil as necessary to bring the oil level within the SAFE range (between the holes) on the dipstick. Do NOT overfill.
24. Reinstall the dipstick and lock the lever.
25. Reinstall the cargo box fasteners and torque to 31 in-lbs (3.5 Nm).
26. Reinstall the lower access panel.
27. On 2-passenger models, secure the two quarter-turn latches from the panel and the two quarter-turn latches inside the center console. On 4-passenger models, ensure the lower retaining tabs are fully engaged. Secure with the two quarter-turn latches.
28. Reinstall the top access panel by fastening the four (4) quarter-turn latches.
29. Reinstall the seats.
30. On 2-passenger models, slide the seat tabs at the front edge onto the seat retainer tubes. Press down firmly at the rear of the seat to engage the rear latches. Ensure the seats are latched securely. On 4-passenger models, reinstall the seat backs by aligning the bottom alignment tabs and pushing down to fully engage. Push in on the seat back to engage the upper latch.
31. Dispose of the used oil, filter and rags properly at your local recycling center.
For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
TORX® is a registered trademark of Acument Intellectual Properties, LLC
YouTube® is a registered trademark of Google LLC
Unless noted, trademarks are the property of Polaris Industries Inc.
© 2024 Polaris Industries Inc.
