Skip to content Skip to navigation Skip to footer
POLARIS OFF-ROAD VEHICLES
HELP CENTER
11/08/2024

RANGER Plow System Kits

Listed below are the plow mount, frame and blade kits for Polaris RANGER vehicles

To order a replacement part for any aspect of your plow system, see your authorized Polaris Dealer. If you need a part not listed, also consult your Polaris Dealer. 

Prior to purchasing, always check the installation instructions to ensure that the kit fits your RANGER and that you have all of the necessary tools and hardware. To only view kits that fit your vehicle, visit the Accessories section of the RANGER website and use the fitment tool, shown below, at the top of the page.

RGR Fitment Tool

MOUNTS

Glacier Pro HD Plow Mount (Part Number 2879106)

Glacier Pro H D Plow Mount

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. The Hardware Kit (part number 2204832) and Lift Rod Kit (part number 2204974) contain replacement parts. To order a part or kit, see your Polaris Dealer. 


Mid-Size Glacier Pro HD Plow Mount (Part Number 2880261)

Mid-Size Glacier Pro H D Plow Mount

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


Glacier HD Plow Mount (Part Number 2879105)

Glacier H D Plow Mount

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. Replacement parts are available in the Hardware Kit (part number 2204831), Lift Rod Kit (part number 2204974) or Front Grille Kit (part number 5257056). To order a part or kit, see your Polaris Dealer. 


Glacier II Plow Mount (Part Number 2879116)

Glacier II Plow Mount

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


FRAMES

Glacier Pro HD Plow Frame (Part Number 2889308)

Glacier Pro H D Plow Frame

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow frame kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. This kit replaces part number 2883255, which uses different installation instructions.

In the event of a collision with an obstacle at a speed greater than what the system is rated for, the angle selection T-Pin (part number 2204827) of the manual angulation mechanism is designed to shear to minimize the force of impact to the pushframe.

If the angle selection T-pin is broken, inspect all components of the plow system to see if any other system components have been damaged. If a part is damaged, the impact speed was greater than what the system is designed to support. You must then buy a replacement from your dealer.

Angle Selection T Pin

Should you need to replace the angle selection T-Pin, a spare pin is provided in the angle lever. Follow the steps below to change your T-Pin:

Shear Pin Location

1. Remove the R-Pin (62) and the clevis pin (61) that keep the angle lever (28) in place. 

2. Lift the angle lever and remove the spare T-Pin (31). 

3. Remove the two tension springs (39) retaining the T-Pin.

4. Remove the two pieces of broken T-Pin.

5. Insert the new T-Pin.

6. Replace the angle lever.

7. Reinstall the clevis pin and the R-Pin.

8. Reinstall the two tension springs. 

Note: Visit your Authorized Polaris Dealer to order a new T-Pin, part number 2204827, and replace the original spare you just removed in the event of an additional hard impact failure. The T-Pin is designed only to protect against the impacts affecting right and left ends of the blade. The T-Pin does not protect the system from a central impact. Always inspect the entire system in the event of a hard impact to ensure that no damage occurred to any system components other than the T-Pin.


Glacier Pro HD Push Frame (Part Number 2880260)
Mid-Size Glacier Pro H D Push Frame

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow frame kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 

In the event of a collision with an obstacle at a speed greater than that recommended for the system, the shear pin (part number 2205527) of the manual angle mechanism will break to minimize the force of impact in the frame. 

If the shear pin is broken, inspect the plow system for damaged parts. If any part is damaged, the impact velocity was greater than what the system is designed to support. You must then buy a replacement part from your Polaris Dealer. 

Shear Pin Kit

If only the shear pin is broken, the pin can be removed and installed upside down and used again. Follow these steps to change the pin:

Shear Pin Location

1. Using a long nose pliers, remove the two tension springs (21) and then remove the pin (34) retaining the angle lever (30).

2. Remove the half-broken shear pin (33) and reinsert it upside down. You can get a new spare pin, part number 2205527, from your dealer.

3. Align the hole in the shear pin with the slot in the angle lever and insert the pin securing the parts in place.

4. Use a long nose pliers to reinstall the two tension springs completing the assembly.

Note: The shear pin is designed only to protect against the impacts affecting right and left ends of the plow. The pin does not protect the system from a center impact. Always inspect the entire plow system after a shear pin has failed to ensure no other components were damaged by the impact.


Glacier HD Plow Frame (Part Number 2889307)

Glacier H D Plow Frame

This kit replaces part number 2882927 and uses the same installation instructions. For more information, view the instructions by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow frame kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


Lock & Ride Glacier II Pushframe (Part Number 2878822)

Push frame

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow frame kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


BLADES

Glacier Pro HD Plow Blade - 72-Inch Poly (Part Number 2879317)

Glacier Pro H D Plow Blade 72-Inch Poly

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow blade kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 

Other accessory kits available for purchase are the Plow Markers Kit (part number 2872726) and Hardened Wear Bar Kit (part number 2879875).


Glacier Pro HD Plow Blade - 72-Inch Steel (Part Number 2890334)
Glacier Pro H D Plow Blade

This kit replaces part number 2879874, which uses different installation instructions. For more information, view the instructions for these kits by searching the part number in the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow blade kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 

Other accessory kits available for purchase are the Plow Markers Kit (part number 2872726), Hardened Wear Bar Kit (part number 2879875) and Rubber Snow Deflector Flap Kit (part number 2858541). To order a kit, see your Polaris Dealer.


Glacier Pro Plow Blade - 72-Inch Steel (Part Number 2890335)
Glacier Pro Plow Blade

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow blade kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


Glacier II County Plow Blade - 72-Inch Steel (Part Number 2877736)

Glacier II County Plow Blade

Installation instructions are not available at this time. For more information, see your Polaris Dealer. 


Glacier Pro Plow Blade - 66-Inch Poly (Part Number 2880269)

Glacier Pro Plow Blade 66-inch poly

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow blade kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 

Other accessory kits that are available for purchase are the Plow Marker Kit (part number 2872726), the 66-Inch Hardened Wear Bar Kit (part number 2879868) and the 66-Inch Rubber Deflector Flap Kit (part number 2879866).


Glacier Pro Plow Blade - 66-Inch Steel (Part Number 2879868)

Glacier Pro Plow Steel

For more information, view the instructions for this kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow blade kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 

Other accessory kits that are available for purchase are the Plow Marker Kit (part number 2872726), the 66-Inch Hardened Wear Bar Kit (part number 2879868) and the 66-Inch Rubber Deflector Flap Kit (part number 2879866).

For more on Polaris plow systems, listen to the The What, How and Why of Snow Plowing episode of the Polaris Podcast.
For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
To find replacement parts, view the online parts catalog

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2022 Polaris Industries Inc.

Keyword(s) plow , system , parts , part , replace , replacement , mount , frame , blade , shear ,