Skip to content Skip to navigation Skip to footer
POLARIS OFF-ROAD VEHICLES
HELP CENTER
11/14/2024

GENERAL Plow System Kits

Listed below are the plow mount, frame and blade kits for Polaris GENERAL vehicles. Installation instructions are linked as well, which list the individual parts in each kit. 

To order a replacement part for any aspect of your plow system, see your authorized Polaris Dealer. If you need a part not listed, also consult your Polaris Dealer. 

Prior to purchasing, always check the installation instructions to ensure that the kit fits your GENERAL and that you have all of the necessary tools and hardware. To determine if a mount, frame or blade fits your GENERAL, visit the Accessories section of the GENERAL website. Enter your vehicle information into the fitment tool to determine if the part will fit your vehicle. The fitment tool can be found at the top of every accessory page. 

Fitment Tool

PLOW SYSTEMS

Glacier Pro HD Plow System (Part Number 3880015)

Glacier Pro HD plow system

Installation instructions for the whole system are not available. Installation instructions for each part of the system can be found on the product page. These instructions also list all of the parts included in the kits, their part numbers and which service kits replacements can be found in. The kit includes: Glacier Pro Plow Mount (Part Number 2881763), Glacier Pro HD Push Frame (Part Number 2880260) and Glacier Pro Plow Blade - 66" Poly (Part Number 2880269). To order a part or kit, see your Polaris Dealer. 

Note: Winch required, must be purchased separately.


Glacier HD Plow System (Part Number 3880016)

Glacier HD plow system

Installation instructions for the whole system are not available at this time. Installation instructions for each part of the system can be found on the product page. These instructions also list all of the parts included in the kits, their part numbers and which service kits replacements can be found in. The kit includes: Glacier HD Plow Mount (part number 2883256), Glacier HD Plow Frame (part number 2889307) and Glacier Pro Plow Blade - 66" Steel (part number 2890336). To order a part or kit, see your Polaris Dealer. 

Note: Winch required, must be purchased separately.


Glacier Pro HD with Hydraulics (Part Number 3880014)

Glacier Pro HD hydraulic system

Installation instructions for the whole system are not available at this time. Installation instructions for each part of the system can be found on the product page. These instructions also list all of the parts included in the kits, their part numbers and which service kits replacements can be found in. The kit includes: Glacier Pro Plow Mount (part number 2881763), Glacier Pro HD Push Frame (part number 2880260), Glacier HD Plow Blade - 72" Steel (part number 2890335), Hydraulic Plow Angle (part number 2889052), Plow Control for GENERAL (part number 2883391), Glacier Plow Markers - Pair (part number 2872726) and Replacement HD Rubber Deflector (part number 2858541). To order a part or kit, see your Polaris Dealer. 

    Note: Winch required, must be purchased separately.


    MOUNTS

    Glacier Pro Plow Mount (Part Number 2881763)

    Glacier Pro Plow Mount

    For more information, view the instructions for this part kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


    Glacier HD Plow Mount (Part Number 2883256)

    Glacier HD Plow Mount

    For more information, view the instructions for this part kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 
     

    Discontinued: Glacier II Plow Mount (Part Number 2881762). For more information, view the installation instructions.


    FRAMES

    Mid-Size Glacier Pro HD Push Frame (Part Number 2880260)​​​​​​

    Mid-Size Glacier Pro H D Push Frame

    For more information, view the instructions for this part kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 

    In the event of a collision with an obstacle at a speed greater than that recommended for the system, the shear pin (2205527; 33) of the manual angle mechanism will break to minimize the force of impact in the frame. If the shear pin is broken, inspect the plow system for damaged parts. If any part is damaged, the impact velocity was greater than what the system is designed to support. you must then buy a replacement part from your Polaris Dealer.

    Shear Pin Kit

    If only the shear pin is broken, the pin can be removed and installed upside down and used again. Follow these steps to change the pin:

    1. Using a long nose pliers, remove the two tension springs (21) and then remove the pin (34) retaining the angle lever (30).
    Shear pin replacement diagram

    2. Remove the half-broken shear pin (33) and reinsert it upside down. You can get a new spare pin (part number 2205527) from your Polaris Dealer.

    3. Align the hole in the shear pin (33) with the slot in the angle lever (30) and insert the pin (34), securing the parts in place.

    4. Use a long nose pliers to reinstall the two tension springs (21), completing the assembly.

    Note: The shear pin is designed only to protect against the impacts affecting right and left ends of the plow. The pin does not protect the system from a central impact. It's important to always inspect the entire plow system after a shear pin has filed to ensure no other components were damaged by the impact.


    Glacier HD Plow Frame (Part Number 2889307)

    Glacier H D Plow Frame

    For more information, view the instructions for this part kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


    Lock & Ride Glacier II Pushframe (Part Number 2878822)​​​​​​

    Push frame

    For more information, view the instructions for this part kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


    BLADES

    Glacier Pro Plow Blade - 72-Inch Steel (Part Number 2890335)

    Glacier Pro Plow Blade

    For more information, view the instructions for this part kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


    Glacier Pro Plow Blade - 66-Inch Poly (Part Number 2880269)

    Glacier Pro Plow Blade 66-inch poly

    For more information, view the instructions for this part kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 


    Glacier Pro Plow Blade - 66-Inch Steel (Part Number 2890336)

    Glacier Pro Plow Steel

    For more information, view the instructions for this part kit by searching the Polaris Accessory Installation Instruction Site. These instructions also list all of the parts included in the plow mount kits, their part numbers and which service kits replacements can be found in. To order a part or kit, see your Polaris Dealer. 

    Discontinued: 60-Inch Snow Blade (Part Number 2876626). Replacement part numbers: 60-inch wear bar (part number 2871806), heavy duty skid shoes (which come as a pair) (part number 2873423), standard skid shoes (which come as a pair) (part number 2877245) and deflector for the 60-inch blade (part number 2871808). Installation instructions are not available at this time. ​​​​​​

    ADDITIONAL ACCESSORIES

    For more on Polaris plow systems, listen to the The What, How and Why of Snow Plowing episode of the Polaris Podcast.
    For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
    To find replacement parts, view the online parts catalog

    Unless noted, trademarks are the property of Polaris Industries Inc.
    © 2022 Polaris Industries Inc.

    Keyword(s) plow , system , mount , blade , frame , part , parts , replace , replacement ,