Passer au contenu de la page Passer à la navigation Passer au pied de page
POLARIS OFF-ROAD VEHICLES
CENTRE D'AIDE
08/27/2024

2023+ RANGER XP Kinetic Rear Axle Removal and Installation

Required Tools and Supplies
15mm, 19mm, 27mm Sockets15mm Wrench15mm Crowfoot Wrench
RatchetTorque WrenchBreaker Bar
PliersFlathead ScrewdriverAnti-Seize
Wire Hanger, Rope or Retention StrapUpper Bearing Carrier NutBrake Caliper Fasteners
Cotter PinShop RagsSafety Glasses & Nitrile Gloves


To learn more about tools, read the Tools and Fasteners Guide

To remove and install the rear axle on your RANGER XP Kinetic, follow these steps:

1. Park the vehicle on a flat, level surface, ensure it is in PARK and remove the key. 

2. Remove the center cap from the wheel. 

3. Using a pliers, remove and discard the cotter pin.

4. Loosen the axle nut with a 27mm socket. 

5. Using a 19mm socket and breaker bar, loosen the lug nuts while the vehicle is on the ground but do not remove at this time.

6. Safely elevate the vehicle. Reference your Owner’s Manual for proper lifting techniques. 

7. Once safely elevated, remove the lug nuts and set aside. 

8. Remove the wheel and set aside. 

9. Using a 15mm wrench, remove and discard the upper and lower caliper mounting fasteners.

10. Carefully remove the caliper from the hub and support it with a wire hanger, rope or retention strap to avoid damaging the brake line.

11. Remove the castle nut and cone washer and set aside.

12. Pull the front wheel hub off the front wheel assembly and set aside.

13. Using a 15mm socket and wrench, remove the upper bearing carrier fastener, nut, and washer, and discard the nut.

14. Tilt the bearing carrier down while pivoting the end of the axle out of the carrier.

15. With a quick, sharp jerk, remove the axle from the transmission.

16. Clean the anti-seize off the axle splines using a clean, dry cloth.

17. Remove and discard the O-ring on the axle. 

18. If reusing the axle, remove and discard the compression ring with a flathead screwdriver. 

19. Inspect the threads and splines on the axle for nicks or burrs and replace if needed.

20. Inspect the CV boots to ensure there are no cuts, wear, or damage and replace if needed.

21. Install a new compression ring into the groove on the end of the axle and ensure it is fully seated. 

22. Install a new O-ring onto the axle.

23. Apply new anti-seize to the splines on both ends of the axle.

24. Inspect the bearing carrier bushings and pivot tube for damage and wear and replace as necessary. When reinstalling the bushings, ensure the non-tapered side is inserted into the carrier. Also, ensure the carrier bushing is fully installed inside the carrier before installing the pivot seals. Tip: Use a flathead screwdriver to assist in this step.

25. Before installing, inspect the anti-seize on the gearcase and hub assembly for dirt or debris. Clean and apply new anti-seize if necessary.

26. Align the splines on the axle with the transmission and push in firmly on the shaft until the compression ring is fully engaged.

27. Lightly pull on the axle to ensure the compression ring is fully engaged.

28. Rotate the bearing carrier up onto the axle and align the mounting holes on the upper A-arm.

29. Reinstall the upper bearing carrier fastener from the front of the vehicle and secure with the retained washer and a new nut. Torque the fastener to 44 ft-lbs (60 Nm). 

30. Insert the axle through the wheel hub and push the hub in until fully seated.

31. Reinstall the washers, with the domed side out, and reinstall the castle nut.

32. Carefully slide the caliper assembly onto the brake disc ensuring the brake rotor is between the two pads.  Before continuing ensure any items used to secure the brake caliper are removed from the wheel well.

33. Install new upper and lower caliper mounting fasteners and use a crowfoot wrench to torque to 46 ft-lbs (62 Nm). 

34. Reinstall the wheel on the vehicle and tighten the lug nuts until fully seated.

35. Safely lower the vehicle until the tires begin to touch the ground. This will help keep the wheel in place when torquing. 

36. Once lowered, torque the lug nuts to 120 ft-lbs (163 Nm) in a crisscross pattern. 

37. Torque the castle nut to 180 ft-lbs (245 Nm). 

38. Continue by inserting a new cotter pin, and bend around the castle nut to secure. If necessary, tighten the castle nut to align the cotter pin holes.

39. Push the dust cap onto the wheel and ensure it is fully seated.

40. Lower the vehicle completely. 

For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2023 Polaris Industries Inc.

Mots-clés video , fix , maintenance , rear , axle , xp kinetic , kinetic ,