Passer au contenu de la page Passer à la navigation Passer au pied de page
POLARIS OFF-ROAD VEHICLES
CENTRE D'AIDE
08/25/2023

2014-2020 Sportsman 570 Wheels and Brake System Inspection and Tire Rotation

Required Tools and Supplies
Nitrile GlovesSafety Glasses
Shop RagsTread Depth Gauge
Brake Rotor Measurement ToolTire Pressure Gauge
FlashlightBrake Pad Measurement Tool
Brake FluidT20 TORX® Socket
17mm SocketRatchet
Torque WrenchBreaker Bar

For more information on tools, read Tools and Fasteners Guide.

Always wear safety glasses and nitrile gloves when servicing your Polaris ATV. To inspect the wheels and brake system and perform a tire rotation on your model year 2020 and older Sportsman 570, Sportsman 570 Utility or Sportsman Touring 570, follow these steps:

1. Take a close look at each tire. 

  • Verify there is sufficient tread depth. Tires should be replaced once they reach one-eighth inch or 3 millimeters of tread depth.
  • Inspect for damage that may compromise the integrity of the tire.
  • Inspect the tire pressure and verify it is set to specification. The tire pressure should be 7 psi (48.3 kPa) on all tires.
  • Take a close look at how the tires are wearing. If there is irregular wear, it may be time for a rotation.

2. Inspect the fluid level and condition in the front master cylinder, located on the left handlebar. 

3. If fluid is needed, clean the area with a clean cloth. 

4. Remove the two cover fasteners with a T20 TORX® socket.

5. Lift the cover off and set aside. 

6. Remove the diaphragm and set aside. Do not allow brake fluid to contact painted surfaces, or paint damage may occur.

7. Add fluid as needed. Do not overfill. A 12-ounce (355 ml) bottle of DOT 4 Brake Fluid is part number 2872189.

8. Reinstall the diaphragm, cover and fasteners. Torque the fasteners to 84 in-lbs (10 Nm).

9. Remove the seat by pulling up on the rear and pivoting back.

  • Inspect the rear brake master cylinder and ensure the fluid level is between the MIN and MAX marks.  
  • Add fluid as needed and reinstall the seat, ensuring the front retainers are properly engaged.

10. Using a 17mm socket, loosen the lug nuts before the vehicle is off the ground. Do not remove.

  • Then safely elevate the vehicle. Reference your Owner’s Manual for proper lifting techniques.
  • Remove the lug nuts and set aside. 
  • Remove the wheels and set aside.
  • Follow the front brake lines from the front reservoir to the front junction block in the center of the chassis frame. 
  • Continue inspecting the brake lines to both front calipers, looking for any leaks, kinks or damage.
  • Ensure the brake line retainers are properly secured.
  • Inspect the connections at the front brake calipers for leaks or damage. 
  • Move back to the junction block and inspect the rear brake line running along the left side of the vehicle and to the rear master cylinder.    
  • Inspect the brake line connection at the master cylinder for leaks and continue following both lines back to the rear caliper.
  • Inspect both connections at the rear brake caliper for leaks.

11. Take a look at the brake pads and rotors. Always allow the brakes to cool completely before performing inspection to prevent the risk of burns.

  • Check the brake pad thickness using a suitable tool. Be sure to check the thickness on the inside pads as well. Replace any brake pads that are worn beyond their minimum thickness of 0.180 inches (4.6mm).
  • Use a brake rotor micrometer to measure the thickness of the brake rotors. Replace if worn below the minimum thickness of 0.140 inches (3.556 mm) in the front and 0.170 inches (4.318 mm) in the rear.
  • If inspection reveals any concerns, do NOT attempt to drive the vehicle. See your authorized Polaris Service Center.

12. Next, the tires can be rotated, if applicable, and reinstalled. Due to different configurations, some wheels may not be able to be rotated. Always pay attention to all markings and directional indicators on the tires.

  • Install the wheels on the vehicle and hand tighten the lug nuts.
  • Safely lower the vehicle until the tires begin to touch the ground. This will help keep the wheels in place when torqueing. 
  • Torque the lug nuts to specification in a crisscross pattern. Torque steel wheels to 27 ft-lbs (37 Nm). Torque aluminum wheels to 30 ft-lbs (41 Nm) plus a quarter-turn.
  • Lower the vehicle completely.

For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

TORX® is a registered trademark of Acument Intellectual Properties, LLC
YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2022 Polaris Industries Inc.