Passer au contenu de la page Passer à la navigation Passer au pied de page
POLARIS OFF-ROAD VEHICLES
CENTRE D'AIDE
11/13/2023

2020+ Scrambler XP 1000 S Suspension Adjustments

Your Polaris Scrambler XP 1000 S features multiple suspension adjustments. Note that it can be helpful to record your preferred settings and any adjustments you make prior to test rides. Make only one adjustment at a time when determining what settings work best for you and your riding style. Note that the adjustments listed are for stock vehicles. Accessories, rider profile and skill level all play roles in how your suspension handles. Tire pressure also will affect how the vehicle handles. All tires should be set to specification. 

Preload Adjustments
Changes in preload affect the distribution of weight between the front and rear of the vehicle. Increasing preload on a shock will increase the ride height and transfer the weight away from the shock you are adjusting. When adjusting the front preload, always adjust the left and right shocks equally. Preload can be adjusted to rider preference for trail performance or to compensate for carrying cargo.

Suspension diagram

Front/Rear Spring Preload Adjustment
The factory setting is appropriate for nearly all riding conditions. If desired, the suspension may be adjusted to maintain vehicle clearance height when carrying loads. 

The factory setting is 15.63 in (39.7 cm) for the front suspension and 15.56 in (39.5 cm) for the rear suspension. 

preload spring adjustment

To adjust the preload:

1. Elevate the vehicle to allow the suspension to fully extend. 

2. Turn the adjusting ring to the left to increase preload and ride height. Turn the adjusting ring to the right to decrease preload and ride height. 

Follow these guidelines if you make adjustments to the front or rear spring preload:

  • Always return the suspension to the factory setting after the load is removed from the vehicle. The increased suspension height will negatively impact vehicle stability when operating without a load. 
  • Do not increase the spring preload by more than 1 inch (25.4 mm) over the factory setting. 
  • When decreasing preload, make sure at least two turns of preload are holding the spring between the retainer on the top of the shock and the threaded spring preload adjuster nut on the shock body. Failure to do so could cause the retainer to fall off when the suspension is fully extended. 

Crossover Ring Adjustment
The factory setting is 2 inches (5 cm) for the front suspension. 

crossover ring adjustment

Your shock is made up of two springs. The first spring has a softer spring rate for the initial compression. The second one has a stiffer spring rate to keep your vehicle from bottoming out. The crossover ring separates the two and determines when the spring rate changes.

To increase stiffness, move the crossover rings down. To decrease stiffness, move the crossover rings up.

To adjust the crossover rings, do the following:

1. Elevate the vehicle to allow the suspension to fully extend.

2. Using a screwdriver, unlock the crossover adjustment ring. 

3. Adjust the crossover ring to the desired location.

4. Lock the crossover adjustment ring. 

Damping Adjustments
Compression and rebound damping adjustments are a matter of rider comfort. A stiffer ride means the rider will absorb more of the energy created by the impact. On a softer ride, the suspension absorbs more of the impact energy. Increased damping means a stiffer ride, while decreased damping means a softer ride. 

High/Low Speed Compression Adjustment
Scrambler XP 1000 S models are equipped with high and low speed compression adjustments. The high-speed clicker will change how the shock absorbs frequent large impacts, like on a bumpy trail. Low-speed adjustments change how the shocks react to less frequent, more gradual impacts, such as on hilly terrain or when transitioning from downhill to uphill riding. 

Always adjust the clicker at least one click below full stiff (full clockwise) or shock damage will occur. 

The factory setting is 8 clicks from full stiff for the front/rear high-speed suspension and 5 clicks from full stiff for the front/rear low-speed suspension. 

high and low compression adjustments

To adjust the high speed compression:

1. Turn the red outside clicker (1) clockwise to increase compression damping. 

2. Turn the red outside clicker (1) counterclockwise to decrease high speed compression damping. 

To adjust the low speed compression:

1. Turn the black inside clicker (2) clockwise to increase compression damping. 

2. Turn the black inside clicker (2) counterclockwise to decrease low speed compression damping. 

Rebound Damping Adjustment
Rebounding damping determines how quickly your suspension decompresses after impact. The stiffer the rebound adjuster is set, the slower the suspension decompresses. This means the shock and spring will extend at a slower rate after impact and make for a stiffer ride. The softer the rebound adjuster is set, the faster the suspension decompresses. The shock and spring will extend at a faster rate and make for a bouncier ride. Most riders will want to find a setting that is soft enough to provide a comfortable riding experience without compromising vehicle control and handling.

The factory setting for the rebound adjuster is 5 clicks from full stiff. 

rebound damping adjustment

To adjust rebound damping:

1. Turn the adjuster clockwise to increase rebound damping and stiffness. The maximum adjustment is fully turned in. 

2. Turn the adjuster counterclockwise to decrease rebound damping and stiffness. The minimum adjustment is 9 clicks out from the maximum position. 

For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2022 Polaris Inc.