Skip to content Skip to navigation Skip to footer
POLARIS COMMERCIAL
HELP CENTER
06/10/2024

2023 Pro XD Mid-Size Gas Wheel and Brake System Inspection and Tire Rotation

Required Tools and Supplies

  • 14mm Socket
  • Torque Wrench
  • Breaker Bar
  • Brake Pad Measurement Tool
  • Tire Pressure Gauge
  • Tread Depth Gauge
  • Brake Fluid
  • Eye Protection
  • Nitrile Gloves
  • Shop Rags

For information on tools, read the Tools and Fasteners Guide. Always wear safety glasses and nitrile gloves when servicing your Polaris vehicle.

To inspect the wheels and brake system and perform a tire rotation on your Pro XD Mid-Size Gas, follow these steps.

1. Take a close look at each tire. 

  • Inspect for damage that may compromise the integrity of the tire.
  • Verify there is sufficient tread depth. Tires should be replaced once they reach one-eighth inch or 3 millimeters of tread depth.
  • Inspect the tire pressure and verify it is set to specification. Reference the Owner’s Manual or tire pressure label on your vehicle for the correct specification.
  • Take a close look at how the tires are wearing. If there is irregular wear, it may be time for a rotation.

2. Inspect the fluid level and condition in the master cylinder, located in the driver’s side front wheel well. Ensure the level is between the min and max marks. 

  • If needed, turn the two quarter turn latches on the hood and slide forward to remove.
  • Clean around the cap and remove to add fluid. Keep in mind that if the fluid is low, you may have a leak or worn brake pads. Do not allow brake fluid to contact painted surfaces or paint damage may occur.
  • Align the mounting tabs on the hood and sliding into place.
  • Secure the hood by turning the two quarter turn latches.

3. Remove the tires from the vehicle. 

  • Loosen the lug nuts while the vehicle is on the ground with a 14mm socket with breaker bar, but do not remove them at this time.
  • Safely elevate the vehicle. Reference your Owner’s Manual for proper lifting techniques.
  • Once safely elevated, remove the lug nuts and set aside. 
  • Remove the wheels and set aside. 

4. Inspect the banjo bolts on the passenger side of the master cylinder for leaks. 

  • Follow the lines all the way to the front calipers, looking for any leaks, kinks or damage. Also, ensure the brake line retainers are properly secured.
  • Inspect the connections at the front brake calipers for leaks.
  • Follow the brake lines to the rear of the vehicle, checking for leaks, kinks and damage. 
  • Inspect the connections at the junction block in the driver’s rear wheel well for leaks.
  • Follow the brake line to the rear brake calipers, looking for leaks, kinks and damage. Also, ensure the brake line retainers are properly secured.
  • Inspect the rear brake calipers and connections for leaks. 
  • If inspection reveals any concerns, do NOT attempt to drive the vehicle. See your authorized Polaris Service Center

5. Take a look at the brake pads. Always allow the brakes to cool completely before inspecting to prevent the risk of burns.

  • Check the brake pad thickness using a suitable tool. Be sure to check the thickness on the inside pads as well and replace any pads that are worn beyond their minimum thickness, which is 0.030 inches (0.762mm).
  • New front brake pads are part number 2205949. New rear brake pads are part number 2203318.

6. The tires can be rotated, if applicable, and reinstalled. Due to different configurations, some wheels may not be able to be rotated. Always pay attention to all markings and directional indicators on the tires.

  • Install the wheels on the vehicle and hand tightening the lug nuts.
  • Safely lower the vehicle until the tires begin to touch the ground. This will help keep the wheels in place when torquing. 
  • Once lowered, torque the lug nuts to 36 ft-lbs (49 Nm).
  • Lower the vehicle completely.

For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2023 Polaris Industries Inc.

Keyword(s) video , wheel , brake , rotate , inspect , mid , gas ,