Always wear safety glasses and nitrile gloves when servicing your snowmobile. Before you ride your Polaris TITAN SP 155 or TITAN XC 155, perform the pre-ride inspection as described in your Owner’s Manual.
Warning: Read, understand and follow all of the instructions, warnings and safety precautions in the Owner’s Manual and on all product labels. Failure to follow these instructions, warnings and safety precautions could result in serious injury or death.
When performing your pre-ride inspection, do the following:
1. Visually inspect the vehicle, looking for debris, leaks and worn components that may impair the vehicle’s operation.
2. Remove both front side panels by releasing the rubber strap and turning the two quarter-turn latches on each side panel. Pull the panels out and remove from the vehicle.
3. Starting on the left side of the sled, inspect the condition of the drive belt, looking for any looseness, fraying, missing cogs, burns, abrasions or damage.
4. Next, inspect the injection oil level in the oil tank and add oil as necessary.
5. Move over to the right side of the sled and inspect the brake pads and rotor for any corrosion, nicks or burrs.
6. Inspect the coolant level in the overflow bottle. Add coolant as needed. Caution: Escaping steam can cause burns. Never remove the pressure cap while the engine is warm or hot.
7. Remove the three push rivets securing the console.
8. Remove the transmission fill plug with a 6mm Allen socket and check the fluid level. Add fluid if necessary.
9. Reinstall the fill plug. Torque to 12 ft-lbs (16 Nm).
10. Reinstall the three push rivets.
11. Reinstall both side panels by aligning the tabs at the top and bottom. Then secure the rubber straps and quarter-turn latches.
12. Move to the front suspension and inspect for fastener tightness on the shock assembly, control arms, tie rods and spindle.
13. Then inspect for leaks and damage.
14. Inspect the skis for any damage or wear. Replace if necessary.
15. Lift up the skis and inspect the skags for wear. Warning: Worn skags may adversely affect handling, causing loss of control and severe injury or death. See your dealer's studding chart for recommended skags.
16. Next, safely elevate the snowmobile per the Owner’s Manual guidelines to inspect the rear suspension.
17. Inspect the front torque arm limiter strap for wear or damage. Replace if necessary.
18. Continue by inspecting the rail slides for wear. Replace if worn to the wear limit indicator groove.
19. Measure the track tension per the Owner's Manual guidelines. Adjust as necessary. Notice: Tension adjustments should be made only after the track has been warmed up.
20. Next, inspect the track for proper alignment by looking through the track windows in the rear. Ensure they are evenly spaced apart. Adjust as necessary.
21. Continue by inspecting the rear idler wheel bolt and adjusting bolt locknuts for tightness.
22. Safely lower the vehicle to the ground after completing the rear suspension inspection.
23. Next, ensure smooth operation of the steering system by turning the skis from full left to full right.
24. Slowly pull the recoil rope out and inspect the handle and rope for any excessive wear.
25. Ensure proper fluid level in the brake fluid reservoir. Tip: Use a flashlight to illuminate the brake fluid reservoir.
26. Operate the brake and throttle levers, taking note of any binding or sticking.
27. Ensure proper operation of the parking brake.
28. Start the engine and ensure there are no warning lights present.
29. Next, inspect the headlights, taillight and brake light for proper operation.
30. Push the engine stop switch to stop the engine and ensure it does not restart.
31. Restart the engine and ensure the engine turns off when the ignition switch is turned off.
32. Finish the inspection by ensuring there is enough fuel for your trip.
For more information, see your authorized Polaris Dealer. To find a dealer near you, use the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
YouTube® is a registered trademark of Google LLC
Unless noted, trademarks are the property of Polaris Industries Inc.
© 2022 Polaris Industries Inc.