Passer au contenu de la page Passer à la navigation Passer au pied de page
POLARIS OFF-ROAD VEHICLES
CENTRE D'AIDE
11/21/2024

2025 RZR Pro S and Pro XP Wheel and Brake System Inspection and Tire Rotation



Required Tools and Supplies

  • 19mm Socket
  • Torque Wrench
  • Breaker Bar
  • Brake Pad Measurement Tool
  • Tire Pressure Gauge
  • Tread Depth Gauge
  • Brake Fluid
  • Eye Protection
  • Nitrile Gloves
  • Shop Rags

For information on tools, read the Tools and Fasteners Guide. Always wear safety glasses and nitrile gloves when servicing your Polaris RZR.

To inspect the wheel and brake system and perform a tire rotation on your RZR Pro S or Pro XP, follow these steps:

1. Park the vehicle on a flat, level surface, ensure it is in PARK and remove the key.

2. Take a close look at each tire. 

  • Inspect for damage that may compromise the integrity of the tire.
  • Verify there is sufficient tread depth. Tires should be replaced once they reach one-eighth inch or 3 millimeters of tread depth.
  • Inspect the tire pressure and verify it is set to specification. Reference the owner’s manual or tire pressure label on your vehicle for the correct specification.
  • Take a close look at how the tires are wearing. If there is irregular wear, it may be time for a rotation.

3. Remove the wheels from the vehicle. 

  • Loosen the lug nuts with a 19mm socket with breaker bar while the vehicle is on the ground, but do not remove the lug nuts at this time.
  • Safely elevate the vehicle. Reference your Owner’s Manual for proper lifting techniques.
  • Once safely elevated, remove the lug nuts, and set aside. 
  • Remove the wheels and set aside. 

4. Inspect the fluid level and condition in the master cylinder, located in the driver’s side front wheel well. Ensure the level is between the upper (MAX) and lower (MIN) level lines. If it is low, clean around the cap and add brake fluid as necessary from a new and unopened bottle. The recommended brake fluid is DOT 4 Brake Fluid, part number 2872189. Apply the brake forcefully for a few seconds and check for fluid leakage around the fittings. Note: Do not allow brake fluid to contact painted surfaces or paint damage may occur.

  • Check the brake system for fluid leaks.
  • Check the brake pedal for excessive travel or a spongy feel.
  • Check the friction pads for wear, damage and looseness.
  • Check the brake discs for signs of cracks, excessive corrosion, warping or other damage. Clean any grease using an approved brake cleaner or alcohol.

5. Take a look at the brake pads. Note: Always allow the brakes to cool completely before inspecting to prevent the risk of burns.

  • Check the brake pad thickness using a suitable tool. Be sure to inspect the brake disc spline and pad wear surface for excessive wear. Replace any pads that are worn beyond their minimum thickness, which is 0.03 in (0.762 mm). The recommended front brake pads are part number 2211640, and the recommended rear brake pads are part number 2211643Note: If inspection reveals any concerns, Do NOT attempt to drive the vehicle. See your authorized Polaris Service Center. 


6. Once the brake system inspection has been completed, the tires can be rotated and reinstalled. A tire rotation is recommended every 500-miles (805 km). Perform the tire rotation on the vehicle as shown.
Diagram of how to rotate RZR tires

7. Rotate the wheels as needed based on wheel configuration. 

  • Place the wheel on the hub with the valve stem toward the outside and if applicable, point the rotation arrows pointing toward forward rotation.
  • Attach the lug nuts and finger-tighten.
  • Safely lower the vehicle until the tires begin to touch the ground. This will help keep the wheels in place when torquing.
  • Once lowered, torque the lug nuts to specification in a crisscross pattern. For the aluminum wheels, torque to 120 ft-lbs (163 Nm). For the hub retaining nut, torque to 88.5 ft-lbs (120 Nm). 
  • Lower the vehicle completely.

For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2024 Polaris Industries Inc.

Mots-clés video , wheel , brake , rotate , inspect , rzr , pro s , pro xp ,