Passer au contenu de la page Passer à la navigation Passer au pied de page

2019-2024 Pro XD Full-Size Diesel Oil and Filter Change

Required Tools and Supplies

  • 22mm Socket
  • Ratchet
  • Torque Wrench
  • 2.5-Inch (64 mm) Oil Filter Wrench
  • Polaris Diesel HD Engine Oil (part number 2879832)
  • Drain Plug Washer
  • Oil Pan
  • Oil Filter (part number 3070549)
  • Funnel
  • Eye Protection
  • Nitrile Gloves
  • Shop Rags

For information on tools, read the Tools and Fasteners Guide. Always wear safety glasses and nitrile gloves when servicing your Polaris vehicle. For optimal performance, always use Polaris-recommended fluids as described in your Owner’s Manual.

To change the oil and filter on your Pro XD Full-Size Diesel follow these steps.

1. Park the vehicle on a flat, level surface in a well-ventilated area, and ensure the transmission is in PARK.

2. Stop the engine and allow it to cool down.

3. Place a drain pan under the engine crankcase. Tip: Placing a rag in the bottom of the drain pan will help prevent the splashing of oil.

4. Clean the area around the oil drain plug.

5. Remove the drain plug with a 22mm socket, and allow the oil to drain completely. 

6. Position a shop rag underneath the oil filter to catch spillage.

7. Use an oil filter wrench to turn the oil filter counterclockwise to remove it.

8. Using a clean dry cloth, clean the filter sealing surface on the crankcase and ensure the old O-ring is completely removed. 

9. Lubricate the O-ring on the new oil filter with a film of fresh engine oil. Check to make sure the O-ring is in good condition.

10. Install the new filter and rotate it clockwise by hand until the filter gasket contacts the sealing surface, then turn it an additional 3/4 turn.

11. Once the filter is installed, wipe up any residual oil. Note: Ensure there are no shop rags left in the engine bay.

12. Clean any dirt or debris from the drain plug, and ensure the sealing surfaces are free of any burrs, nicks or scratches. 

13. Remove the old sealing washer, and install a new one (part number 3070504) on the drain plug. 

14. Reinstall the drain plug, and torque to 12 ft-lbs (16 Nm).

15. Remove all cargo from the cargo box and pull on the cargo box release lever to tilt the box.

16. Carefully clean around the oil cap.

17. Remove the oil cap and setting it aside.

18. Add the proper amount of Polaris Diesel HD Engine Oil (SAE 5W-40) through the oil fill cap. Do not overfill. The fluid capacity is 3.9 qt (3.7 L). Tip: Add oil slowly, to make sure oil does not get into the breather or intake.

19. Reinstall the oil fill cap and wipe up any residual oil. 

20. Verify the engine is still in PARK and start the engine and allow it to idle for 30 seconds.

21. Stop the engine and inspect the vehicle for leaks. Wait at least 15 seconds before removing the dipstick.

22. Remove the oil dipstick and wipe with a clean shop towel. Reinstall the dipstick fully and remove again to inspect the oil level.

23. Reinstall the dipstick and wipe up any residual oil. 

24. Lower the cargo box and make sure the latch is secure. 

25. Once complete, the maintenance reminder can be reset in the instrument cluster.

  • Turn the key on and hold the MODE button to enter the Options Menu.
  • Navigate to Service Hours.
  • Press the MODE button to select it and use the up and down arrows to adjust the service hours to a new setting if desired (break-in 50 hours, 200 hours thereafter). 
  • Once you have reached your desired setting, press the MODE button again to reset the reminder. 

26. Dispose of the used oil and filter properly at your local recycling center.

For more information, see your authorized Polaris Commercial Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2023 Polaris Industries Inc.