Saltar al contenido Saltar a navegación Saltar al pie de página
POLARIS OFF-ROAD VEHICLES
CENTRO DE AYUDA
07/19/2024

2025 RANGER XP 1000 Oil and Filter Change

Required Tools and Supplies

The Full Synthetic Oil Change Kit is part number 2879323 and the Extreme Duty Oil Change Kit is part number 2890057. These kits include oil, oil filter and drain plug washer. 

For information on tools, read the Tools and Fasteners Guide. Always wear safety glasses and nitrile gloves when servicing your Polaris RANGER. For optimal performance, always use Polaris-recommended fluids as described in your Owner's Manual.

To perform an oil and filter change on your RANGER XP 1000, follow these steps:

1. Park the vehicle on a flat, level surface in a well-ventilated area, ensure the transmission is in PARK and remove the key.

2. Allow the engine to cool down before performing this procedure. 

3. Place a drain pan under the engine crankcase. Tip: Placing a rag in the bottom of the drain pan will help to prevent the splashing of oil.

4. Clean the area around the oil drain plug.

5. Remove the drain plug with a 6mm Allen socket, and allow the oil to drain completely. Caution: Hot oil can cause burns to skin. Do not allow hot oil to contact skin.

6. Remove all cargo from the cargo box and pull up on the cargo box release lever to tilt the box up.

7. Place a rag under the oil filter to catch any spillage.

8. Use an oil filter wrench and turn the filter counter-clockwise to remove.

9. Using a clean dry cloth, clean the filter sealing surface on the engine crankcase.

10. Lubricate the O-ring on the new oil filter with a film of fresh engine oil. Check to make sure the O-ring is in good condition. A new oil filter is part number 2540086

11. Install the new filter and rotate it clockwise by hand until the filter gasket contacts the sealing surface, then turn it an additional 3/4 turn. 

12. Replace the sealing washer on the drain plug. A new sealing washer is part number 5812232Note: The sealing washer on the drain plug should be clean and free of burrs, nicks or scratches. 

13. Reinstall the engine crankcase drain plug and torque to 12 ft-lbs (16 Nm).

14. Clean the area around the oil fill cap.

15. Remove the oil fill cap and fill the engine with the recommended amount of engine oil. The capacity is 2.5 qts (2.4 l). 1 gallon of PS-4 Full Synthetic Engine Oil is part number 2876245 and 1 quart of PS-4 Full Synthetic Engine Oil is part number 2876244

16. Verify the transmission is still in PARK and start the engine, allowing it to idle for 30 seconds.

17. Stop the engine and inspect for leaks. Wait at least 15 seconds before removing the dipstick.

18. Unlock the dipstick lever and remove the dipstick and wipe it dry with a clean shop rag.

19. Re-install the dipstick and push it into place. Do not lock the dipstick. Notice: Make certain the dipstick is threaded all the way into the dipstick tube to keep the depth of the dipstick consistent.

20. Remove the dipstick and check the oil level.

21. Add the recommended oil as necessary to bring the oil level within the SAFE range on the dipstick. Do not overfill.

22. Reinstall the oil fill cap, oil dipstick and the lock lever.

23. Lower the cargo box. 

24. Dispose of the used oil and filter properly at your local recycling center.

For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2024 Polaris Industries Inc.

Palabra (s) clave maintenance , change , changing , replacing , draining , drain , replace , oil , filter , funnel , pan ,