|Required Tools and Supplies|
|6mm Allen Socket||Nitrile Gloves|
|Ratchet||Fluid Suction Device (Suction Method)|
|Torque Wrench||T40 TORX® Socket (Front Cover Method)|
|Fluid Filler||10mm Socket (Front Cover Method)|
|Shop Rags||Drain Pan (Front Cover Method)|
|Safety Glasses||Prying Tool (Front Cover Method)|
This procedure requires the use of chaincase lubricant (part number 2873105).
For more information on tools, visit the Tools and Fasteners Guide. Always wear safety glasses and nitrile gloves when servicing your Polaris snowmobile.
This video will outline the pump and front cover methods that can be used to change the chaincase fluid on a Polaris INDY VR1 with an 850 engine.
1. Ensure the sled is on a flat, level surface.
2. Set the parking brake.
3. Clean the area around the fill plug. Placing a rag under the fill plug will help catch any escaping fluid.
4. Remove the fill plug with a 6mm Allen socket and set aside.
5. To extract the fluid using the pump method:
- Safely elevate the front of the snowmobile using a floor jack or appropriate lift.
- Insert the tube of the suction device into the fill hole. Direct the hose toward the bottom front area of the cover, away from the chain and sprocket.
- Extract the oil using the suction device.
- Then safely lower the snowmobile to fill the chaincase.
6. To drain the fluid using the front cover method:
- Remove the right side panel by turning the three quarter-turn latches. Pivot the panel away from the sled and pull out to remove.
- Remove the fastener on the lower right side of the console using a T40 TORX® socket.
- Remove the push rivet securing the lower right portion of the console with a pliers.
- Continue by removing the push rivet underneath securing the right fender to the footrest. If equipped with a battery, remove the battery and bracket. The full procedure can be found in 2021+ 850 INDY VR1 Battery Removal and Installation.
- Remove the two fasteners securing the lower fender to the chaincase using a T40 TORX® socket.
- Place a drain pan underneath the chaincase. Placing a rag in the bottom of the drain pan will help prevent the splashing of fluid.
- With a 10mm socket, loosen but do not remove the three lower chaincase cover fasteners.
- Carefully pry the cover open on the cover tab. DO NOT insert a screwdriver or pry bar between the cover and chaincase, or seal damage may occur.
- Allow the fluid to drain completely.
- Reinstall the three cover fasteners and torque to 11 ft-lbs (15 Nm).
7. Fill the chaincase through the fill plug hole until fluid reaches the bottom threads and begins to spill out.
8. Clean any dirt or debris from the fill plug.
9. Inspect the O-ring on the plug and replace if necessary.
10. Reinstall the fill plug and torque to 48 in-lbs (6 Nm).
11. Clean any residual fluid off the vehicle and properly dispose of the used fluid.
12. Reinstall the fasteners securing the lower fender to the chaincase.
13. If needed, reinstall the battery bracket and battery. Connect the positive cable first.
14. Reinstall the push rivet underneath the console.
15. Install the push rivet on the lower-right portion of the console.
16. Reinstall the lower console fastener and torque until fully seated.
17. Reinstall the side panel by inserting the upper tab and pivoting in to engage the lower tab.
18. Latch the three quarter-turn latches to secure the panel.
Looking for information on adjusting your drive chain tension? Read 2021+ 850 INDY VR1 Drive Chain Tension Adjustment.
For more information, see your authorized Polaris Dealer. To find a dealer near you, use the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
TORX® is a registered trademark of Acument Intellectual Properties, LLC.
YouTube® is a registered trademark of Google LLC
Unless noted, trademarks are the property of Polaris Industries Inc.
© 2022 Polaris Industries Inc.