Skip to content Skip to navigation Skip to footer
POLARIS OFF-ROAD VEHICLES
HELP CENTER
11/05/2024

2015+ Sportsman 850 and XP 1000 Wheel/Brake System Inspection and Tire Rotation

Required Tools and Supplies:

  • Safety Glasses
  • Nitrile Gloves
  • Shop Rags
  • Brake Rotor Measurement Tool
  • Tread Depth Gauge
  • Tire Pressure Gauge
  • Flashlight
  • Brake Pad Measurement Tool
  • Screwdriver
  • T20 TORX®, T30 TORX® and 17mm Sockets
  • Ratchet
  • Breaker Bar
  • Torque Wrench

For more information on tools, read the Tools and Fasteners Guide.

Always wear safety glasses and nitrile gloves when servicing your Polaris ATV. To inspect the wheel and brake system and to perform a tire rotation on your Sportsman 850 or Sportsman XP 1000, follow these steps:

1. Take a close look at each tire. 

  • Verify there is sufficient tread depth. Tires should be replaced once they reach one-eighth inch or 3 millimeters of tread depth.
  • Inspect for damage that may compromise the integrity of the tire.
  • Inspect the tire pressure and verify it is set to specification. The tire pressure should be 7 psi (48.3 kPa) for all tires. 
  • Take a close look at how the tires are wearing. If there is irregular wear, it may be time for a rotation.

2. Remove the tires. 

  • Use a 17mm socket to loosen the lug nuts while the vehicle is on the ground. Do not remove.
  • Safely elevate the vehicle. Reference your Owner’s Manual for proper lifting techniques.
  • Remove the lug nuts and set aside. 
  • Remove the wheels and set aside.

3. Now is a great time to look at the brake system. Start with the front brake system.

  • Inspect the fluid level and condition in the front master cylinder, located on the left handlebar. 
  • Add fluid as needed by removing the two T20 TORX® fasteners. Caution: After opening a bottle of brake fluid, always discard any unused portion. Brake fluid rapidly absorbs moisture from the air, which causes the boiling temperature to drop. This can lead to early brake fade and the possibility of an accident or serious injury.
  • Follow the lines all the way to the front junction block in the center of the chassis frame. 
  • Continue inspecting the brake lines to both front calipers, looking for any leaks, kinks or damage.
  • Also, ensure the brake line retainers are properly secured.
  • Inspect the connections at the front brake calipers for leaks or damage. 

4.    Next take a look at the brake pads and rotors. Caution: Brake rotors can become extremely hot after operation. Allow the rotors to cool completely before performing maintenance to prevent risk of burns.

  • Check the brake pad thickness using a suitable tool. Be sure to check the thickness on the inside pads as well. Replace any brake pads that are worn beyond their minimum thickness of 0.180 inches (4.6 mm).
  • Use a brake rotor micrometer to measure the thickness of the brake rotors and replace if worn below the minimum thickness of 0.167 inches (4.24 mm).

5. Next, inspect the rear brake system.

  • Unlatch the front storage compartment and pull back to open. Lift out the storage tray. 
  • Remove the push rivet on the front cover trim. Then use a T30 TORX® socket to remove the two fasteners and pull the front cover trim out.
  • Inspect the rear brake master cylinder and ensure the fluid level is between the min and max marks.  
  • Reinstall the front cover trim panel. Install the trim panel fasteners and torque until fully seated. Then install the push rivet. 
  • Reinstall the storage tray by aligning the front tabs and pivoting down. Secure the quarter-turn latches and verify the sealing gasket is properly seated. 
  • Close the front storage compartment and secure the front latches. 
  • Follow the brake line back to the rear of the vehicle, looking for leaks, kinks and damage. 
  • Continue following the brake line to the rear brake caliper, ensuring the brake line retainers are properly secured.
  • Inspect the connection at the rear brake caliper. If inspection reveals any concerns, do NOT attempt to drive the vehicle. See your authorized Polaris Service Center.

6. Once the brake system inspection has been completed, the tires can be rotated, if applicable, and reinstalled. Rotate the wheels as needed based on wheel configuration. Caution: Due to different configurations, some wheels may not be able to be rotated. Always pay attention to all markings and directional indicators on the tires.

  • Install the wheels on the vehicle and hand tighten the lug nuts.
  • Safely lower the vehicle until the tires begin to touch the ground. Reference your Owner’s Manual for proper lowering techniques.
  • Torque the lug nuts to specification in a crisscross pattern. Aluminum wheels should be torqued to 75 ft-lbs (102 Nm). Steel wheels should be torqued to 45 ft-lbs (61 Nm). 
  • Lower the vehicle completely.

For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

TORX® is a registered trademark of Acument Intellectual Properties, LLC
YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2021 Polaris Industries Inc.